Optex FA Narrow Aperture and Wafer Mapping Fiber Cables

Narrow Aperture and Wafer Mapping Fiber Cables

With a narrow emitting angle of as small as 2 degrees, narrow aperture fibers are well suited for wafer mapping in the semicon industry.

Documents

Optex FA NF Wafer Mapping Fiber Series Brochure - 446 k

Product Compare (0)

Sort By:

Show:

Optex NF-DR09 Diffuse R1 Mapping Fiber Square Head-On Sense

Rectangular Sensing Head Wafer Mapping Fiber ..

Order Now, Call for Lead Time

$285.00

Optex NF-RG01 Retro-reflective Mapping Fiber Narrow View

Retroreflective Narrow Beam Fiber Optic Cable With only a 3degree aperture this retroreflective sens..

Order Now, Call for Lead Time

$410.00

Optex NF-TG01 Tbeam Mapping Fiber Head-on 2° Aperture

Thrubeam Mapping Fiber ..

Available: 4

$215.00

Optex NF-TG02 Ø4 Cylindrical R1 Mapping Fiber Side-View 2° Aperture

Mapping Fiber ..

Available: 8

$300.00

Optex NF-TG03 Tbeam Mapping Fiber Side-view 2° Aperture

Thrubeam Mapping Fiber ..

Available: 7

$285.00

Optex NF-TG04 Tbeam Mapping Fiber Side-view 3° Aperture

Wafer Mapping Side View Fiber Optic Cable ..

Available: 4

$410.00

Optex NF-TS12 Tbeam Mapping Fiber Side-View 5° Aperture

Thrubeam Wafer Mapping Fiber Side View ..

Available: 5

$260.00

Optex NF-TS22 Tbeam Mapping Fiber Side-View 3° Aperture

Thrubeam Wafer Mapping Fiber Side View 3 degree Aperture ..

Order Now, Call for Lead Time

$480.00

Optex NF-TS22H Tbeam 105°C Mapping Fiber Sideview 3° Aperture

Wafer Mapping Thrubeam Heat Resistant ..

Available: 2

$800.00

Optex NF-TS22M Tbeam 105°C Mapping Fiber Sideview 3° Aperture

Wafer Mapping Side View Fiber Optic Cable ..

Available: 3

$670.00

Optex NF-TS23 Tbeam 105°C Mapping Fiber sideview 2.5° Aperture

Available: 1

$770.00

Optex NF-TS25 Tbeam 105°C Mapping Fiber sideview 2.5° Aperture

Available: 3

$670.00

Optex NF-TS27 Tbeam 200°C Mapping Fiber sideview 2.5° Aperture

Wafer Mapping Side View Fiber Optic Cable ..

Available: 1

$1,900.00

Showing 1 to 13 of 13 (1 Pages)


IV Bag Seal Detection	Glass Bottle Detection Through Hole	High-Temp Glass Bottle Detection	Height Confirmation in Dropper
DR-Q series high-precision laser sensor designed for transparent detection can check for faulty seals by looking for a slight protrusion of the thin seal.	DR-Q150T series' small coaxial laser beam can look through small hole in the guide and detect the transparent bottles.	NF-DH01 high temp diffuse reflective, when paired with a high temp reflector, can reliably detect transparent bottles in high temp environment.	D3IF-TN amplifier & NF-TW01 water sensor can check for proper height of chemical solution in a dropper.
Solution: Optex DR-Q Series	Solution: Optex FA DR-Q150T	Solution: Optex NF-DH01	Solution: D3IF-TN and NF-TW01


Bend & Warp Measurement	Cap Slope Inspection	Metal Thickness Measurement	Assembled Height / Parallel Inspection
LS-100 two-dimenational laser array sensor is used to measure warp and bending of a linear slide.	LS-100 series two-dimensional laser array is used to check for proper cap placement on bottle.	Two CD22 series lasers and the CDA-M controller are used to measure the thickness of a metal sheet.	Four CD22 series lasers along with two CDA controllers and the UC1-Cl11 CC link master check levelness on an assembled part in a tight space.
Solution: Optex FA LS Series	Solution: Optex FA LS Series	Solution: Optex FA CD22 Series	Solution: Optex FA CD22 Series


Cap Color Sorting	O-Ring Detection	Metal Fitting Sizing	Sorting by Diameter
DM-18T series RGB color sensor is used to detect the wrong color cap.	BGS-HL series high precision laser sensor can check for absence of o-ring on a round part and remove them from the production line.	DSTA-200 30mm array laser is used to sort metal fittings by detecting size differences.	NF-TZ09 array fiber and D3RF fiber amplifier is used to sort parts by diameter differences.
Solution: Optex FA DM-18T	Solution: Optex FA BGS-HL Series	Solution: Optex FA DSTA-200	Solution: NF-TZ09 and D3RF


Belt Alignment / Misalignment	Measuring Mounting Position	Engine Block Detection	Checking for Seated Parts
The LS series beam array measurement sensor can be used to check for misalignment during bonding of of rubber belts.	Two CD22 laser measurement sensors can be used to determine correct position of metal plates for mounting.	The ZM series with a stainless steel housing provides excellent oil and water resistance, perfect for an oily environment.	The TOF-L series time of flight laser can be used to confirm parts are seated properly in work cells. Sensing range up to 4.5m.
Solution: Optex FA LS Series	Solution: Optex FA CD22 Series	Solution: Optex FA ZM Series	Solution: Optex FA TOF-L Series