Stable Detection even in Foggy Environments

A large projecting and receiving lens result in a strong projected beam. Ideal for use in tough conditions like a foggy atmosphere.

Excellent Color Response Out to 500mm

The BGS-2V50 sensor is capabale of detecting various reflective objects out to 500mm without being influence by background object. Below is a color response chart.

Multi Voltage Version with Relay Output

DC24-240V AC24-240V Relay Rated 3amps at 240VAC

V2 Photoelectric Series Specs
Sensing Mode / Type	Background Suppression
Sensing Distance	150 to 500mm
Resolution / Min Detectable Object	1mm or less
Light Source	Red LED
Supply Voltage	24 to 240 Volt AC/DC
Current Consumption	3VA
Response Time	15ms
Sensitivity Adjustment	2-turn potentiometer
Output	SPDT relay 3 amp AC
Output Operation Mode	L/O mode
Material	Case/cover ABS (glass reinforced) Lens: PC
Protection	IP67
Shock Rating	50G
Temperature	-25 to 55° C
Connection	2 meter cable
Includes	Mounting bracket/screws

Optex BGS-2V50 AC/DC Background Suppression 150 to 500mm SPDT relay 2M cable

Manufacturer: Optex FA
Part #: BGS-2V50
Availability: 10

$125.00

Qty

Stable Detection even in Foggy Environments

Excellent Color Response Out to 500mm

Multi Voltage Version with Relay Output

Optex BGS-2V50 AC/DC Background Suppression 150 to 500mm SPDT relay 2M cable

$125.00

Related Products

LV2-S01


IV Bag Seal Detection	Glass Bottle Detection Through Hole	High-Temp Glass Bottle Detection	Height Confirmation in Dropper
DR-Q series high-precision laser sensor designed for transparent detection can check for faulty seals by looking for a slight protrusion of the thin seal.	DR-Q150T series' small coaxial laser beam can look through small hole in the guide and detect the transparent bottles.	NF-DH01 high temp diffuse reflective, when paired with a high temp reflector, can reliably detect transparent bottles in high temp environment.	D3IF-TN amplifier & NF-TW01 water sensor can check for proper height of chemical solution in a dropper.
Solution: Optex DR-Q Series	Solution: Optex FA DR-Q150T	Solution: Optex NF-DH01	Solution: D3IF-TN and NF-TW01


Bend & Warp Measurement	Cap Slope Inspection	Metal Thickness Measurement	Assembled Height / Parallel Inspection
LS-100 two-dimenational laser array sensor is used to measure warp and bending of a linear slide.	LS-100 series two-dimensional laser array is used to check for proper cap placement on bottle.	Two CD22 series lasers and the CDA-M controller are used to measure the thickness of a metal sheet.	Four CD22 series lasers along with two CDA controllers and the UC1-Cl11 CC link master check levelness on an assembled part in a tight space.
Solution: Optex FA LS Series	Solution: Optex FA LS Series	Solution: Optex FA CD22 Series	Solution: Optex FA CD22 Series


Cap Color Sorting	O-Ring Detection	Metal Fitting Sizing	Sorting by Diameter
DM-18T series RGB color sensor is used to detect the wrong color cap.	BGS-HL series high precision laser sensor can check for absence of o-ring on a round part and remove them from the production line.	DSTA-200 30mm array laser is used to sort metal fittings by detecting size differences.	NF-TZ09 array fiber and D3RF fiber amplifier is used to sort parts by diameter differences.
Solution: Optex FA DM-18T	Solution: Optex FA BGS-HL Series	Solution: Optex FA DSTA-200	Solution: NF-TZ09 and D3RF


Belt Alignment / Misalignment	Measuring Mounting Position	Engine Block Detection	Checking for Seated Parts
The LS series beam array measurement sensor can be used to check for misalignment during bonding of of rubber belts.	Two CD22 laser measurement sensors can be used to determine correct position of metal plates for mounting.	The ZM series with a stainless steel housing provides excellent oil and water resistance, perfect for an oily environment.	The TOF-L series time of flight laser can be used to confirm parts are seated properly in work cells. Sensing range up to 4.5m.
Solution: Optex FA LS Series	Solution: Optex FA CD22 Series	Solution: Optex FA ZM Series	Solution: Optex FA TOF-L Series