Multifunction Amplifier with Easy Setup

Basic setup is as easy as pressing the teach button for 2 seconds. more advanced functions are located in a deeper setup layer for solving more complex applications

Adjustable Hysteresis

Hysteresis can be adjusted from 1% to 40%. This enables the sensor to be optimized for detecting slight differences in parts or applications with a lot of vibration

Optex designed processor designed for High Speed Long Distance

As fast as 16 microsecond response time for the stand alone versions and 22 microseconds for the interconnect versions. Utilizing a new method of emitting the beam the D3RF Series has increased sensing distances by as much as 5 times over previous generations of fiber amplifiers.

Fiber Specs - Amps
Sensing Mode - Type	Fiber Optic Amplifier
Features	Dual 4 Digit Display
Sensitivity Adjustment	PB teach with 2-button fine adjust
Supply Voltage	12 to 24 VDC
Light Source	Red LED
Indicators	Dual Digital LEDs Light Level (Red) Threshold (Green)
Model Type	Stand-Alone Type
Cross-Talk Prevention	Up to 16 amplifiers w/master-slave
LED Power Level Control	Settable levels: 100%, 50%, and 25%
Current Consumption	39mA Max - 25mA max: 1ch/Power Saving Mode
Response Time	Settable: (7 Levels) from 16µs to 8ms
Output	NPN
Output Operation Mode	Light-on / dark-on selectable
Timer/Counter Option	Programmable time delay or up/down counter
Shock Rating	50G
Protection	IP50
Temperature	-25 to 55° C
Connection	2 meter cable
Includes	BEF-WLL170 DIN bracket

Optex D3RF-TN Digital Teach FO Amp Stand-Alone - Red LED NPN - 2M Cable

Manufacturer: Optex FA
Part #: D3RF-TN
Availability: 30

$132.00

Qty

Multifunction Amplifier with Easy Setup

Adjustable Hysteresis

Optex designed processor designed for High Speed Long Distance

Optex D3RF-TN Digital Teach FO Amp Stand-Alone - Red LED NPN - 2M Cable

$132.00

Related Products

Optex NF-DZ02 Diffuse w/ 10.85mm Beam Array Metal Hsg

Optex NF-TZ09 Tbeam R1 Fiber w/ 11mm Beam Array


IV Bag Seal Detection	Glass Bottle Detection Through Hole	High-Temp Glass Bottle Detection	Height Confirmation in Dropper
DR-Q series high-precision laser sensor designed for transparent detection can check for faulty seals by looking for a slight protrusion of the thin seal.	DR-Q150T series' small coaxial laser beam can look through small hole in the guide and detect the transparent bottles.	NF-DH01 high temp diffuse reflective, when paired with a high temp reflector, can reliably detect transparent bottles in high temp environment.	D3IF-TN amplifier & NF-TW01 water sensor can check for proper height of chemical solution in a dropper.
Solution: Optex DR-Q Series	Solution: Optex FA DR-Q150T	Solution: Optex NF-DH01	Solution: D3IF-TN and NF-TW01


Bend & Warp Measurement	Cap Slope Inspection	Metal Thickness Measurement	Assembled Height / Parallel Inspection
LS-100 two-dimenational laser array sensor is used to measure warp and bending of a linear slide.	LS-100 series two-dimensional laser array is used to check for proper cap placement on bottle.	Two CD22 series lasers and the CDA-M controller are used to measure the thickness of a metal sheet.	Four CD22 series lasers along with two CDA controllers and the UC1-Cl11 CC link master check levelness on an assembled part in a tight space.
Solution: Optex FA LS Series	Solution: Optex FA LS Series	Solution: Optex FA CD22 Series	Solution: Optex FA CD22 Series


Cap Color Sorting	O-Ring Detection	Metal Fitting Sizing	Sorting by Diameter
DM-18T series RGB color sensor is used to detect the wrong color cap.	BGS-HL series high precision laser sensor can check for absence of o-ring on a round part and remove them from the production line.	DSTA-200 30mm array laser is used to sort metal fittings by detecting size differences.	NF-TZ09 array fiber and D3RF fiber amplifier is used to sort parts by diameter differences.
Solution: Optex FA DM-18T	Solution: Optex FA BGS-HL Series	Solution: Optex FA DSTA-200	Solution: NF-TZ09 and D3RF


Belt Alignment / Misalignment	Measuring Mounting Position	Engine Block Detection	Checking for Seated Parts
The LS series beam array measurement sensor can be used to check for misalignment during bonding of of rubber belts.	Two CD22 laser measurement sensors can be used to determine correct position of metal plates for mounting.	The ZM series with a stainless steel housing provides excellent oil and water resistance, perfect for an oily environment.	The TOF-L series time of flight laser can be used to confirm parts are seated properly in work cells. Sensing range up to 4.5m.
Solution: Optex FA LS Series	Solution: Optex FA CD22 Series	Solution: Optex FA ZM Series	Solution: Optex FA TOF-L Series