ZD-L40CN Key Features:

Compact size: 11mm W x 32mm H
Fine 2mm beam spot at 400mm distance
Affordable cost
Class 2 laser
NPN output
M8 4 pin quick disconnect
Cross-talk prevention for two sensors
Amplifier built-in

Fine 2mm Beam Spot at 400mm Distance

Approx. ø2 mm spot size at a distance of 400 mm. Optimal for applications that in which small object detection and high repeat accuracy are required.

Great for High-Speed Production Lines - Response Time: 250 μs

The laser sensor provides a high-speed response time of 250 μs that makes detection in high speed production lines possible.

Outstanding Environmental Resistance

Degree of protection: IP67, Shock resistance: 50 G.

Its integrally molded structure enables all models to conform to IP67 and achieve a shock resistance up to 50 G. It doesn't break even when wet and can be used in locations where vibrations are generated.

Standard Spec Dimensions - 25.4mm Standard Pitch

Features an industry standard pitch of 25.4 mm.

Characteristic Data

ZL Series Specs
Sensing Mode	Diffuse
Features	Long distance sensing with pin-point beam. Cross-talk prevention for two sensors
Operation Voltage	10 to 30VDC
Current Consumption	30mA
Light Source	Red Laser Diode 650nm
Light Source Output	3mW
FDA Laser Class	Class II
Sensing Distance	400mm
Spot Size	2mm at 400mm
Repeatability	0.5mm
Hysteresis	20% at 400mm
Sensitivity Adjustment	Potentiometer 1-turn
Display	LED Indicator
External Input	Laser Off
Response Time	250µs
Control Output	NPN
Timing Option	N/A
Housing	ABS
Operation Temperature	-10 to +50° C
Protection	IP 67
Connection	M8 4P QD
Includes	BEF-W100-A Mounting Bracket

Optex ZD-L40CN Compact Diffuse Laser Sensor - 400mm Sensing Range - NPN - M8 4 Pin Quick Disconnect

Manufacturer: Optex FA
Part #: ZD-L40CN
Availability: 4

$128.00

Qty


IV Bag Seal Detection	Glass Bottle Detection Through Hole	High-Temp Glass Bottle Detection	Height Confirmation in Dropper
DR-Q series high-precision laser sensor designed for transparent detection can check for faulty seals by looking for a slight protrusion of the thin seal.	DR-Q150T series' small coaxial laser beam can look through small hole in the guide and detect the transparent bottles.	NF-DH01 high temp diffuse reflective, when paired with a high temp reflector, can reliably detect transparent bottles in high temp environment.	D3IF-TN amplifier & NF-TW01 water sensor can check for proper height of chemical solution in a dropper.
Solution: Optex DR-Q Series	Solution: Optex FA DR-Q150T	Solution: Optex NF-DH01	Solution: D3IF-TN and NF-TW01


Bend & Warp Measurement	Cap Slope Inspection	Metal Thickness Measurement	Assembled Height / Parallel Inspection
LS-100 two-dimenational laser array sensor is used to measure warp and bending of a linear slide.	LS-100 series two-dimensional laser array is used to check for proper cap placement on bottle.	Two CD22 series lasers and the CDA-M controller are used to measure the thickness of a metal sheet.	Four CD22 series lasers along with two CDA controllers and the UC1-Cl11 CC link master check levelness on an assembled part in a tight space.
Solution: Optex FA LS Series	Solution: Optex FA LS Series	Solution: Optex FA CD22 Series	Solution: Optex FA CD22 Series


Cap Color Sorting	O-Ring Detection	Metal Fitting Sizing	Sorting by Diameter
DM-18T series RGB color sensor is used to detect the wrong color cap.	BGS-HL series high precision laser sensor can check for absence of o-ring on a round part and remove them from the production line.	DSTA-200 30mm array laser is used to sort metal fittings by detecting size differences.	NF-TZ09 array fiber and D3RF fiber amplifier is used to sort parts by diameter differences.
Solution: Optex FA DM-18T	Solution: Optex FA BGS-HL Series	Solution: Optex FA DSTA-200	Solution: NF-TZ09 and D3RF


Belt Alignment / Misalignment	Measuring Mounting Position	Engine Block Detection	Checking for Seated Parts
The LS series beam array measurement sensor can be used to check for misalignment during bonding of of rubber belts.	Two CD22 laser measurement sensors can be used to determine correct position of metal plates for mounting.	The ZM series with a stainless steel housing provides excellent oil and water resistance, perfect for an oily environment.	The TOF-L series time of flight laser can be used to confirm parts are seated properly in work cells. Sensing range up to 4.5m.
Solution: Optex FA LS Series	Solution: Optex FA CD22 Series	Solution: Optex FA ZM Series	Solution: Optex FA TOF-L Series